Hagglund Options

WIDE TRACK VERSION

Longer leaf springs, drive shafts, additional fenders, results in +14cm width of undercarriage (for front and rear car), overall width: 2000mm, standard width of track 620mm


SUPERWIDE TRACK VERSION

Longer leaf springs, drive shafts, additional fenders 2000mm, results in +34 width of undercarriage (for front and rear car), overall width: 2200mm


LONG TRACK VERSION

For rear car, consists of a stretched undercarriage with extended main beam and track beams, one set of extra road wheels, extra torsion springs and swing arms, and longer tracks. Payload 2640kg on the rear car instead of 2200kg standard. The extension is 500mm.
*only in combination with wide track version 2000mm


HYDRAULIC TILT SYSTEM

Additional hydraulic cylinder above articulated steering for tilting front and rear car, lockable for ditch crossing, including electromagnetic controlled hydraulic valve and all necessary installation, switches at dashboard area. No extra hydraulic system necessary (driven by steering system).


DIFF LOCK FOR FRONT AND/OR REAR CAR

Consisting of a special cast aluminum housing for the diff, special multiple disc clutch, oil hydraulic piston, special shaft and gear wheels. Provides 100% traction on each track on drivers demand. Includes an electrohydraulic activation system, switch and control light at the dashboard. Fully installed. No extra hydraulic system necessary. Driven by steering system.


WINCH (A)

Consisting of winch, front mounting, hydraulic, 3 tonnes pull, waterproof, quick mounting system (removable by a single person), with internal brake, pressure valve, with cable and safety hook, including hydraulic couplings and hoses


BRACKET FOR REAR MOUNT OF WINCH

Mounting system (removable by single person), including hydraulic couplings and hoses, trailer coupling hook goes into quick mounting bracket


HYDRAULIC SYSTEM FOR WINCH (B)

Consisting of double gear pump, tank, filters, lines, hoses, pto front for winch, 1 section valve (in/out), fully installed


WINCH SYSTEM (combination of A + B)

Hydraulic system for winch consisting of hydraulic pump, filter, 1 section valve, couplings, hoses, lines, hydraulic tank


WINCH

Consisting of winch, front mounting, hydraulic, 3 tonnes pull, quick mounting system (removable by a single person in), with internal brake, pressure valve with cable and safety hook, including hydraulic couplings and hoses


EXTRA HEATER – WEBASTO COOLANT HEATER

Installed. Programmable timer or remote control


ENGINE BLOCK HEATER

External source 220V block heater, external socket


ICE CLEATS

Traction aids; 32 pcs, recommended


PLATFORM, NON AMPHIBIOUS

Custom made bed for BV206 consisting of longitudinal and cross section members from steel tubing. Steel floor or multiplex floor. Steel frame complete galvanised and painted. Aluminum or steel sideboards. Front fix, rear and side tiltable. Measurements approx. 2900mm x 1800mm x 350 mm. Payload approx. 1800kg. With lashing points, rear lights and electric system.


PLATFORM, AMPHIBIOUS

Custom made bed for BV206 consisting of longitudinal and cross section members from steel tubing. Steel floor. Steel frame complete galvanised and painted. Aluminum sideboards with seals. Front fix, rear and side tiltable. Measurements approx.. 2900mm x 1800mm x 650mm. Payload approx. 1800kg. With lashing points, rear lights and electric system. With bilge pump.


DUMPER BODY

Steel, one-way hydraulic tipping, galvanised steel: custom made dumper body for BV206 consisting of longitudinal and cross section members from steel tubing as basic frame. Rear pivot point, front hydraulic ram for tipping. With hydraulic system and electric system installed. Dump body with steel floor, steel sideboards. Front fix, side fix, rear tiltable and waterproof seal. All steel parts galvanised and painted. Measurements approx. 2700mm x 1800mm (or 2000mm) x 800mm. Payload approx. 1800kg. With lashing points for load, rear lights and electric system. With bilge pump.


PLATFORM and CRANE; NON AMPHIBIOUS

Custom made bed for BV206 consisting of longitudinal and cross section members from steel tubing. Steel floor or Multiplex floor. Steel frame complete galvanised and painted. Aluminum or steel sideboards. Front fix, rear and side tiltable. Measurements approx. 2900mm x 1800mm x 350mm Payload approx. 1500kg With lashing points, rear lights and electric system

CRANE

Palfinger PC 2300, capacity 1800kg @ 2.0m or 380kg @ 5.1m electrohydraulic drive, hydraulic telescoping outriggers (manual pull) (optional PC 3300 crane with 30% more capacity)


PLATFORM and CRANE; AMPHIBIOUS

Custom made bed for BV206 consisting of longitudinal and cross section members From steel tubing. Steel floor. Steel frame complete galvanised and painted. Aluminum sideboards. Front fix, rear and side tiltable , with rubber seals on all sideboards. Measurements approx. 2900mm x 1800mm x 600mm. Payload approx. 1500kg With lashing points, rear lights and electric system. With bilge pump.

CRANE

Palfinger PC 2300, capacity 1800kg @ 2.0m or 380kg @ 5.1m, electrohydraulic drive, hydraulic telescoping outriggers (manual pull) (optional PC 3300 crane with 30% more capacity,)


BRUSH GUARD


PALETIZING SYSTEM – HOOK LIFT HELLGETH HEWL 206-1

Including complete double gear pump hydraulic system for front and rear car, including inox steel oil tank, electric activated valves and cable control unit, complete electric system with sensors, control and wiring, track fenders from aluminum, rear bumper and tail lights. With 4 point locking for amphibious containers. Fully installed and ready for work. Without container, available for original track width 1850mm or 2000mm version.


OIL SPILL BODY WITH OIL SPILL EQUIPMENT

1200 litre reservoir, reservoir galvanised, vacuum pump 54001/min, vacuum performance 8500mm WS, pump can work in vacuum modus and pressure modus, compressor with Vanguard petrol engine 16hp. Complete equipped with hoses and suction nozzle. Mounted on galvanised frame and frame mounted on Hagglunds with fenders, rear lights.


2-WAY RAILWAY TRACK SYSTEM

Complete installed, with front and rear rail guide system mounted to the Hagglund frame. Hydraulically activated. Driver can stay in the car for getting on/off the rail. Sensor system for enabling the driver to get the vehicle in straight steering position for rail driving. With camera system front and rear and monitor to help for getting into position. Including full hydraulic system and complete installation.


HOMOLOGATION BY GERMAN TUV

As used vehicle, “repowered by Hellgeth Engineering” with partially used parts from 1992.


FLAT BED FOR HOOK LIFT HEWL 206-1, WITH SIDEBOARDS

Consisting of main frame with two rear rollers, steel sideboards, front fix, left and ride side, rear tiltable. Steel floor. With lashing points, RAL color codes according to customer needs. Measurements: L 2800mm x W 2000mm (or 1850mm) x H 400mm


FLAT BED FOR HOOK LIFT HEWL 206-1, WITHOUT SIDEBOARDS

Consisting of main frame with two rear rollers, steel floor, lashing points, RAL color codes according to customer needs. Measurements: L 2800mm x W 2000mm (or 1850mm) x H 400mm


WATER PROPULSION SYSTEM

Pump drive shaft for higher torque, high performance hydraulic pump with increased flow and pressure, increased size of suction and pressure hoses and lines. Modified steering system with load sensing signal and priority valve for using steering oil flow additionally. Hydraulic valve unit with forward and reverse mode. 4 hydraulic motors mounted at the center beam, 2 front 2 rear. Power approx. 8kW per motor. 32kW total. One 250mm propeller per motor. With propeller protection. Design speed in water approx. 6kph (speed just driven by tracks 3kph) Jet drive as above, but automatic fold propellers, unfolded 300mm dia, no protection.


SNOW PLOW KIT

8-way snow plow, joystick control, detachable. Fully installed. Needs hydraulic system.


AIR CONDITIONING FOR FRONT AND/OR REAR CAB

Roof mounted, with electric driven compressor and heat exchanger.


ENGINE UPGRADE

To 185hp, modified ECU


HIFI STEREO

System for front car, extra roof panel


FRONT WINDOWS

Heated


REVERSE CAMERA

With monitor at dash, heated camera lens, protection cover, camera on rear car


INTERIOR CAMERA

With monitor at dash and camera inside rear cab, one way intercom system included


REVERSE CAMERA and INTERIOR CAMERA

With one monitor at dash, and 2 cameras. 1st camera on rear car, heated camera lens, protection cover. 2nd camera inside rear cab, one way intercom system included


INTERCOM SYSTEM

Between driver and rear cab passengers


HIGH PERFORMANCE BRAKE KIT

Vented rotor made from cast and larger caliper brackets


ENGINE GOVERNOR

Electronic, load independent governor, keeps the engine at a pre-adjustable level, e.g. for a constant oil flow (to work with a crane) may only be activated in neutral position of automatic gearbox